DM7404N DATASHEET PDF

DMN datasheet, DMN circuit, DMN data sheet: NSC – Hex Inverting Gates,alldatasheet, datasheet, Datasheet search site for Electronic. DMN from Texas Instruments High-Performance Analog. Find the PDF Datasheet, Specifications and Distributor Information. DMN from Fairchild Semiconductor. Find the PDF Datasheet, Specifications and Distributor Information.

Author: Makazahn Fenrir
Country: Kosovo
Language: English (Spanish)
Genre: Business
Published (Last): 28 May 2009
Pages: 439
PDF File Size: 16.37 Mb
ePub File Size: 2.83 Mb
ISBN: 122-8-76870-965-3
Downloads: 71134
Price: Free* [*Free Regsitration Required]
Uploader: Kajitaxe

DM Hex Inverting Gates

Available accessories include a mm 8 inch or mm 16 inch ribbon cable with DIP-type connectors that is compatible with standard 14pin DIP IC sockets orrespectively. Phone or Fax United States: RF Connector Drive Pin e. Switching time is a maximum of 20 milli-seconds, including contact settling time. When you are choosing new equipment, we will help you with product information, including realistic performance specifications and practical recommendations from experienced test engineers.

Attenuator section activation guide Recommended switching sequence: Section electrical diagram With positive voltage applied to the common pin, the state attenuator card or thru dayasheet of a particular section is determined by connecting its attenuator card pin or thru pin to a Although all sections can be switched simultaneously, the attenuator driver must not allow both pins of the same satasheet e. Solenoids are magnetic latching type; drive voltage may be removed after switching.

Altitude, non-operating 13, meters 50, ft. Calibration data is available as Option xx-UK6 and datasheft generated em7404n measurements made by an Agilent network analyzer. Table 2 on page 4 defines recommended attenuator section activation. We strive to ensure that you get the test and measurement capabilities you paid for and obtain the support you need.

Datasheeet following switching sequence ie. Table 1 is a solenoid drive pin and attenuation guide. The A includes an integral power supply with short circuit protection that can simultaneously provide millamps at 24 volts to all contacts for control of the attenuators and switches, so no external power supply is needed. Selection switching Figure 2 shows one attenuator section schematic. Pins relate to pin attenuator header as shown Table 1NOT terminating connector on any attached drive cable.

  ENERGIA EOLIANA REFERAT PDF

Solenoids are available in either 24 volt standard, Option xx15 volt Option xxand 5 volt Option xx ranges to fit your instrument or system requirements. Used with A or A driver 3 Table 2. White 10 RF connector 2. You can post dahasheet and our suppliers will contact you, shortening your procurement process. To search for more components and get quote from supplier, please use our Part Search: Once switched, the units are latched with permanent magnets, capable of withstanding shocks over 10 Gs.

Experienced Agilent engineers and technicians worldwide can help you maximize your productivity, optimize the return on investment of your Agilent instruments and systems, and obtain dependable measurement accuracy for the life of those products. When you receive your new Agilent equipment, we can help verify that it works properly and help with initial product operation. Figure 3 shows a section that has been switched to the attenuator card position note the closed thru line coil contact.

datasyeet Solve problems efficiently and gain a competitive edge by contracting with us for calibration, extra-cost upgrades, out-of-warranty repairs, and onsite education and training, as well as design, system integration, project management, and other professional engineering services. Each section utilizes one solenoid with dual coil windings, one coil to switch in the attenuator card e. It is a second specification on accuracy, and is used in combination with the absolute accuracy specifications to limit maximum allowable variation from nominal.

Search our Inventory for Part Number.

Electronic Components Part Numbers Available at HKinventory.com

It’s a community-based project which helps to repair anything. This provides a complimentary driver for the section which assures that only one solenoid of the pair is activated at a time.

  ASUS A6M MANUAL PDF

Additional circuit design information may be required from the component manufacturers. Insertion loss 40 with a 10 dB step or to cover an attenuation range of dB or 81 dB in 1 dB steps. Insertion loss performance is out- This family of step attenuators offers three connector types. Since the accuracy specifications include margins for frequency response and unit-to-unit variations, calibration data can improve overall measurement uncertainty. At the same time, the internal contacts for the other coil close so that it can be activated when desired.

We offer tailor-made solutions to accelerate procurement process and increase your competitiveness. Solenoid pin and attenuation guide Section: As a section is switched, the internal contacts of the activated coil open, thus shutting off current flow.

Diode protection is required to protect the IC from the solenoid voltage flyback. Current is self-interrupting in less than 20 ms. You can also take advantage of our daily outgoing RFQ and quotation emails.

Datasheet «DM7404»

For operation to This section is intended as a reference datashheet. To help minimize fraudulent activities online, we would like to encourage our members to use our Escrow service, which significantly reduces the risk of fraud. Attenuator switching pinout Table 1. Since current is drawn through the coil for these circuits, inadvertent switching is prevented by datashert the current to 5 mA.

High attenuation accuracy and low SWR are achieved through the use of miniature thin-film attenuation cards composed of high-stability tantalum nitride film on a sapphire substrate.