LEPD Octal Serial Solenoid Driver. EIGHT LOW RDSon DMOS OUTPUTS @ 25°C VCC 5%) 8 BIT SERIAL INPUT DATA (SPI) 8 BIT SERIAL DIAGNOSTIC . LEPD datasheet, LEPD circuit, LEPD data sheet: STMICROELECTRONICS – Octal serial solenoid driver,alldatasheet, datasheet, Datasheet. LEPD datasheet, LEPD circuit, LEPD data sheet: STMICROELECTRONICS – OCTAL SERIAL SOLENOID DRIVER,alldatasheet, datasheet.
|Published (Last):||22 March 2010|
|PDF File Size:||17.44 Mb|
|ePub File Size:||19.77 Mb|
|Price:||Free* [*Free Regsitration Required]|
Status monitor function is available on all output. I LE Changes characteristics, the max. Page 6 Pin description 2 Pin description Figure 2. Dahasheet 1 Block diagram Figure 1. Revision history 6 Revision history Table 6.
Each output has a current limit circuit which limits the maximum output current to at least 1. Any differences would point to a fault on that xatasheet. Each l9822dpd is independently controlled by an output latch and a common Data is transmitted serially to the device using the.
The SCLK input is gated by the. All other trademarks are the property of their respective owners. If the output was programmed ON by clocking in a zero, and a one came back as the di- agnostic bit for that output, the output pin was still high and a short circuit or overload condition exists.
PowerSO pin connection top view Figure 3. Checking for fault conditions may be done in the fol. Pin description 2 Pin description Figure 2.
LEPD Datasheet – OCTAL SERIAL SOLENOID DRIVER from SGS-Thomson Microelectronics
Page datsheet Functional description 4. Byte Timing with Asynchronous Reset. Home – IC Supply – Link. Page 8 Electrical specifications 3 Electrical specifications 3. Clock in the same control byte and observe the diag. Wait microseconds or so to allow the outputs to settle.
Any differences would point to a fault. Multiwatt 15 mechanical data and package dimensions DIM. Clock in the same control byte and observe the diag- nostic data that comes out of the device.
Page 7 LE 2. Page 5 LE 1 Block diagram Figure 1.
(PDF) L9822EPD Datasheet download
Page 13 LE Figure 6. Elcodis is a trademark of Elcodis Company Ltd. Page 3 LE List of tables Table 1. Page 9 LE Table 5. Copy your embed code and put on your site: LE List of tables Table 1.
LEPD Datasheet(PDF) – STMicroelectronics
At the rising edge of CE the shift register data is latched into the parallel latch and the output stages will be actuated by the new data. LE Information in this document is provided solely in connection with ST products.
Once the delay period has elapsed, the output voltages are sensed by the comparators and any output with voltages higher than 1. Page 4 List of figures List of figures Figure 1. Clock in a new control byte.
Page 11 LE 4. Download datasheet Kb Share this page. Clock in a new control byte. This allows the part to overcome any high inrush cur- rents that may flow immediately after turn on.
LEPD datasheet and specification datasheet.
This allows the part to overcome any high inrush cur. Electrical specifications 3 Electrical specifications 3. List of figures List of figures Figure 1.
Page 2 Contents Contents 1 Block diagram. Page datashheet LE Figure 8. LEPD datasheet and specification datasheet Download datasheet. Contents Contents 1 Block diagram. The diag- nostic bits should be identical to the bits that were first clocked in. Page 16 Revision history 6 Revision history Table 6. If the output was programmed OFF by clocking in a k9822epd, and a zero came back as the diagnostic bit for that output, nothing had pulled the output pin high and it must be floating, so an open circuit condition exists for that output.