Precaution in use of LCD Module. (1) Avoid applying excessive shocks to the module or making any alterations or modifications to it. (2) Don’t make extra holes . Features. 1. 5×8 dots with cursor. 2. Built-in controller (KSU or equivalent). 3. Easy interface with 4-bit or 8-bit MPU. 4. +5V power supply. DRAWING. Winstar Dot Matrix LCD Display Module 16×2, LCD Display A – WHA. SPECIFICATIONS. WHA LCD Datasheet. Interface Pin Function .

Author: Memi Vudora
Country: Philippines
Language: English (Spanish)
Genre: Travel
Published (Last): 15 January 2005
Pages: 434
PDF File Size: 15.6 Mb
ePub File Size: 1.59 Mb
ISBN: 886-3-14139-907-1
Downloads: 42765
Price: Free* [*Free Regsitration Required]
Uploader: Dourg

Any potentiometer between 5K and 50K will work. The LCD looks like this:. Do you have any idea where I could find the correct initializing sequence? Of you don’t see them, turn the pot meter slowly from left to right to adjust the contrast. By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that datashete continued use of the website is subject to these policies.

Dot Matrix LCD Display Module 16×2

I believe Arduino has a built-in Liquid Crystal reference and library that can be used to write to all kinds of pin LCD screens. Double check and triple check your code against any datasheet, it will work. The LCD looks like this: Hello I am just dealing with the same problems, except mine show some squares on the screen. Interface SD Card with Arduino. This way you can solder wires to it, solder a connector on it, whatever you want.

You can finetune this setting when we’ve got characters on the display later. Works like an absolute charm!


We can find the descriptions of what each of the signal pins do in the datasheet as well: If your display looks like this, you’re doing datadheet Basil 05 April Thanks a lot for the explanation, Great work!

Thinking back, there’s something about commands, wait times, and busy flags The tutorial is simple for all to understad 11602a get started. About the author This post was writen by Johan van Tongerencreator of this website.

Dot Matrix LCD Display Module 16×2, LCD Display A, A LCD Datasheet – WHA

We use the potmeter to set the contrast of the display. I ran into the same problem years ago and drove myself nuts trying to initialize the thing and wondering whether it was me or the display keeping it from happening.

As an example you can check http: Did not specify resistor value? Low to write to catasheet register; High to read from the register. Unfortunately, we’ll have dtasheet convert the voltage of pins that may send data to the Tessel from the screen down to 3.

Email Required, but never shown. Connect the power and dztasheet contrast next pins 1, 2, and 3. Your mail is safe with me. JoeO Full Member Posts: The LCD has 16 pin holes According to the table shown here the display controller is STU or compatible. With the potentiometer at one end of it’s range the display will be blank and at the other end you should see boxes on the top line of the display. A lot has changed since then and the microcontroller built for me has been made.

Johan is a professional frontend developerpetrolhead and allround DIY-er. CSS-only Clock Intelligent image cropping with focal point image-rendering: The solder should flow into a nice blob. Virgin Galactic — Commercial Space Flight. The voltage at pin 3 should be around 0. datahseet


LCD1602 (5V Blue Backlight)

Hey kylefarrisThis looks like a good first project! LCD Liquid Crystal Display screen is an electronic display module and find a wide range of applications. Chaul on Feb 02, Just mention the resistor value for the light sensor again when you deal with it, it is mentioned in the beginning,but I missed it first time around,excellent tutorial: Finetuning gets a little harder because the range is bigger, but that’s no problem for this tutorial.

Sign up using Email and Password. It worked after I had resoldered the LCD’s pins.

Tessel is a 3. But it works anyway! The command register stores the command instructions given to the LCD. Puzzled me that the lightSensor reading was higher in the dark, but now I get it. They are not what you may think. You won’t be able to use their exact code because it’s in C but it will at least give you a starting point for understanding how to make the screen work from code once the hardware is connected properly. Michael Bean 14 December Excellent!!! Ming 26 July Very Good Tutorial!

I choose to solder the connectors to the back so I could press the LCD display on the breadboard. If you see black squares you’ve already done much of the work.