AP1 Dc-to-dc Converter Control Circuits The is a monolithic control circuit containing the primary functions required for DC-to-DC converters. AP1 datasheet, AP1 circuit, AP1 data sheet: SLS – DC-TO-DC CONVERTER CONTROL CIRCUITS,alldatasheet, datasheet, Datasheet. ORDERING INFORMATION. See general marking information in the device marking section on page 11 of this data sheet. DEVICE MARKING INFORMATION. 1.

Author: Dotaxe Vizahn
Country: Reunion
Language: English (Spanish)
Genre: Music
Published (Last): 7 May 2014
Pages: 496
PDF File Size: 7.55 Mb
ePub File Size: 13.55 Mb
ISBN: 442-3-81001-808-6
Downloads: 49827
Price: Free* [*Free Regsitration Required]
Uploader: Shakree


That drives a Teensy MCU which then provides 3. A single pole double-throw switch or an dqtasheet relay device would serve to switch one phone lead between the bridge or directly to the line to re-enable the ring. The current limit is best at slightly above the max required current.

January 25, at 6: Adding a cheap digital buffer IC could pick up 0. Using a well designed PCB with thick short tracks for the main current paths might save 30 milliohms and give maybe 0. If the MC were suitable for the voltage and current 30463ap1 require, an added advantage of it is that the one part is capable of being utilized in buck, boost, or inverting circuits. A 12v line filter might also be advised, they can be daatasheet from auto stores.

System Logic Semiconductor – datasheet pdf

Just change the 6k8 resistor, to change the output voltage to something other than 5. If you want to invest some effort it can be improved further; 1. CT used the datasheet value of 1nF.


Hi Dan Thanks for sharing. 34063ao1 are a few components that have static values: December 13, at 8: My box interrogates caller ID while the handset is disconnected. Modifying the circuit for high output currents.

AP1 Datasheet ETC pdf data sheet FREE from

Determining the Overall Circuit Layout The way the passive components are connected to the MC depend on what type of power supply you are building: Modifying the circuit for 12v car operation. Energy conversion efficiency is very high due mainly to the choice of external components used with the cheap SMPS IC. I am building a boost circuit, so the overall circuit layout will look like this: L min is 72uH.

Mar 24, 21, 2, Dec 29, 7.

Home Contents About Documents Index. Because the ring signal is AC superimposed on the DC, masking the ring should be a matter of introducing a diode bridge between the phone dtasheet and the handset.

January 22, at 2: The downside is datashfet are a bit noisier than linear regulators. Even the SG that I had initially tried to use is not acceptable either and, if I recall, everything else I looked at was ridiculously expensive if I ever hope to do something commercial with my project. My Watts toroid gives nearly 60V without load, and still Sep 7, 2, You are 340633ap1 using your Twitter account.


The PFET on period is the top of the waveform. This should serve to disable the ring signal for the connected handset without disabling the line for making calls or picking one up because you can hear a ring elsewhere or if you have ESP. 34063qp1

PFET turnon is good at 0. Once my box determines the call can pass, it regenerates caller id for the handset, then connects it back to the telco so I can hear the phone and still see who is calling.

Dec 29, 5.

I arbitrarily decide to use a K ohm resistor for R2 so I just need to do some algebra to determine what R1 must be: Nov 4, It is why SMPS switching mode power supplies are so popular. It is efficient enough to not need a heatsink even at 5v 1. I spent a ridiculous amount of time trying to get an inverting boost power supply working to provide V.

This does not matter and the can datasheeg quite energy efficiency when “stuttering” in discontinuous mode like this.

Posted in Art