ASTM F436 SPECIFICATION PDF

Available in 1/2″ through 2″ bolt sizes as outlined in ASTM F in 5/8″ through /4″ bolt sizes to weathering specification as outlined in ASTM F NOTE 1—Acomplete metric companion to Specification F has been developed—Specification FM; therefore no metric equivalents are presented in this. ASTM F covers the chemical and mechanical requirements for hardened washers in diameters ranging from 1/4″ to 4″ inclusive.

Author: Narn Daijas
Country: Montenegro
Language: English (Spanish)
Genre: Business
Published (Last): 5 February 2014
Pages: 190
PDF File Size: 19.58 Mb
ePub File Size: 14.81 Mb
ISBN: 457-6-74314-322-2
Downloads: 71801
Price: Free* [*Free Regsitration Required]
Uploader: Samudal

F — 10 Standard Speci?

Nominal outside diameter, in. When properly exposed to the atmosphere, these steels can be used bare uncoated for many applications.

Note 1—A complete metric companion to Specification FM has been developed Specification FM ; therefore no metric equivalents are presented in this specification. These washers are intended for general-purpose mechanical and structural use with bolts, nuts, studs, and other internally and externally threaded fasteners. Committee F16 has identi? The atmospheric corrosion resistance of these steels is substantially better than that of carbon steel with or without copper addition.

Each type and style of washer shall be suitably sampled, and should conform to specified values of chemical composition, Rockwell hardness, inside and outside diameter, thickness, and clipped width. This abstract is a brief summary of the referenced standard. Moreover, the styles of washers covered here are: These washers are intended for general-purpose mechanical and structural use with bolts, nuts, studs, and other internally and externally threaded fasteners.

Number of Pieces in Lot and under to to 22 Over 22 Number of Specimens 1 2 3 5 It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

  AMANTUL DOAMNEI CHATTERLEY PDF

Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. The atmospheric corrosion resistance of these steels is substantially better than that of carbon steel with or without copper addition. Materials and Manufacture 4. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Arc and gas cut washers shall be free of metal spatter. Originally approved in These washers are intended for general-purpose mechanical and structural use with bolts, nuts, studs, and other internally and externally threaded fasteners.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior specificatkon use. Steels to be used to manufacture the washers shall be produced by the open-hearth, basic-oxygen, or electric-furnace process.

Packaging and Package Marking Approved May 1, Referenced Documents purchase soecification The documents listed below are referenced within the subject standard but are not provided as part of the standard. Work Item s – specirication revisions of this standard. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. This is acceptable provided that the majority of washers in the lot still display the identi?

Link to Active This link will always route to the current Active version of the standard. Permission rights to photocopy the standard may also be secured from the ASTM website www. Your atm are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. When properly exposed to the atmosphere, these steels can axtm used bare uncoated for many applications. Moreover, the styles of washers covered here are: Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

  CD4518BE DATASHEET PDF

ASTM F436 Structural Washers

Active view current version of standard. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee specificxtion Standards, at the specificstion shown below. It is informational only and not an official part of specificaion standard; the full text of the standard itself must be referred to for its use and application. A Full indicator runout. Each type and style of washer shall be suitably sampled, and should conform to specified values of chemical composition, Rockwell hardness, inside and outside diameter, thickness, and clipped width.

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

No other units of measurement are included in this standard. Combining values from the two systems may result in non-conformance with the standard.

ASTM F – Portland Bolt

Type 1—washers made of carbon steel; and Type 3—washers made of weathering steel. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Credit Information Credit Application.