DIN 50324 PDF

Standard [WITHDRAWN] DIN Tribology; testing of friction and wear model test for sliding friction of solids (ball-on-disc system). Buy DIN TRIBOLOGY; TESTING OF FRICTION AND WEAR MODEL TEST FOR SLIDING FRICTION OF SOLIDS (BALL ON DISC SYSTEM) from. Find the most up-to-date version of DIN at Engineering

Author: Nam Mazutaxe
Country: Sierra Leone
Language: English (Spanish)
Genre: Travel
Published (Last): 26 June 2008
Pages: 175
PDF File Size: 1.67 Mb
ePub File Size: 9.37 Mb
ISBN: 702-6-25552-147-8
Downloads: 92277
Price: Free* [*Free Regsitration Required]
Uploader: Mazukazahn

In this latter case, the results cannot be compared to the ILS data Table 2. The test setup allows to mount real pieces of actual piston ring and liners. However, it must be clearly stated in 503244 report that, while the directions and protocol in Test Method G99 were followed if truethe choices of test parameters were different from Test Method G99 values, and the test results were therefore also different from the Test Method G99 results. Stribeck Curve Stribeck curve is a plot between coefficient of friction and bearing number.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The value of any wear test method lies in predicting the relative ranking of material combinations. Link to Active This link will always route to the current Active version of the standard. Linear Oscillating The 5032 Test to determine extreme pressure, friction wear properties of lubricant greases, solid bonded films, gear and hydraulic fluids, lubricating oils.

  DIETARIO VOLUBLE PDF

Work Item s – proposed revisions of this standard. In all modules listed above user can change the load and velocity to automatically plot Stribeck Curves with ease. Thank you for your interest and filling out the form! Temperature and recirculation addons are also available. Twist Compression is designed to measure friction and adhesion in metal forming.

Such a use of this standard is encouraged as a means to improve wear testing methodology. The standard Test to determine extreme pressure, friction wear properties of lubricant greases, solid bonded films, gear and hydraulic fluids, lubricating oils.

The test involves rotating one ball on three stationary balls at controlled environmental conditions. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Contact us for a live Demo or additional information. Stribeck curve is a plot between coefficient of friction and bearing number. No other units of measurement are included in this standard. Sin time down force controlpiezo sensors to measure inline friction makes this module very reliable and repeatable.

ASTM G99 – 17 Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus

Loads from mN to 10,N. All tests are done in oscillation mode under controlled environmental conditions. Piston Ring Liner This test helps evaluate friction and wear 500324 of piston ring liner material in presence of engine oils. Tapping Torque, Twist Compression, Drilling Tapping torque diin allows to characterize friction, wear, torque etc.

  INTROSCOPE JAVA AGENT GUIDE PDF

Since the pin-on-disk test method does not attempt to duplicate all the conditions that may be experienced in service for example; lubrication, load, pressure, contact geometry, removal of wear debris, and presence of corrosive environmentthere is no insurance that the test will predict the wear rate of a given material under conditions differing from those in the test. The principal areas of experimental attention in using this type of apparatus to measure wear are described.

Fast Exchange makes all these modules easily swapable on the MFT platform. The ball is caused to rub against the disk 1mm stroke at a frequency of 50 Hz for 75 min.

High-load and high-temperature tribometer

Test involves slowly rotating a ring on top of material of choice. The coefficient of friction may also be determined.

The tests can be done in controlled environmental conditions including humidity, temperature and more. This test helps evaluate friction and wear parameters of piston ring liner material in presence of engine oils. Historical Version s – view dinn versions of standard.

Materials are tested in pairs under nominally non-abrasive conditions.