Official Journal of the European Union. EN. Only the original UN/ECE texts have legal effect under international public law. The status and date. Regulation No 46 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of devices for indirect. [ECE-R46 Uniform provisions concerning the approval of rear-view mirrors and of motor vehicles with regard to the installation of rear-view mirrors, MOD].

Author: Vikazahn Viktilar
Country: Sao Tome and Principe
Language: English (Spanish)
Genre: Art
Published (Last): 27 May 2006
Pages: 403
PDF File Size: 13.7 Mb
ePub File Size: 16.91 Mb
ISBN: 346-1-22653-867-4
Downloads: 57903
Price: Free* [*Free Regsitration Required]
Uploader: Kazraktilar

When a mirror is adjustable with respect to the base, the test position shall be that in which any pivoting device is least likely to operate, within the limits of adjustment provided by the applicant; 6. Names and addresses of Technical Services responsible for conducting approval tests, and of Administrative Departments II. The difference between any of the radii of curvature r p1r p2and r p3 and r must not exceed 0,15 r.

InterRegs: Regulation No. | ECE – United Nations

The department may then either:. Photographs, if any, shall show sufficient detail. Sufficiently detailed drawings with the installation instructions: The mirrors are subjected to impact under the following different conditions: The chosen analytical approach es shall be established and maintained by the manufacturer and shall be made open for inspection by the Technical Service at the time of the type approval.

Modifications of the vehicle type and extension of approval Electrical characteristics of the t46 unit. Computer Graphics Lighting Jinxiang Chai.

Devices for Indirect Vision

Address es of assembly plant s: However, breakage of the reflecting surface will be allowed if one of the following conditions is fulfilled: Make trade name of manufacturer: Use the Advanced search. General Specifications The Technical Service shall use recognized test methods to check compliance with the requirements defined above in the Regulation. OJ L If the feet change position, they should be allowed to remain in that attitude for the moment.


The ecw of the segment joining the two ocular points is in a vertical longitudinal plane which shall pass through the centre of the driver’s designated seating position, as specified by the efe manufacturer.

If vehicles of these categories cannot fulfil the requirements by using a front-view device, a vision support system shall be used. Name and address of manufacturer: Where, due to the installation, the distance eye-monitor is more than the critical viewing distance, the maximum obtainable detection distance is defined as: Fields of vision If applicable, name and address of Manufacturer’s representative: In the case of camera-monitor systems, the lens shall not break during the tests described in Paragraph 6.

Address es of the production plant s … 7. Address es of the production plant s: Model of information document for type approval of vehicle with respect to the installation of devices for indirect vision. The first digit is an Arabic numeral and designates the row of seats, counting from the front to the rear of the vehicle.

Help Print this page. In the case of a failure, the driver shall be informed for example by a clear and visible warning signal or message display. Seating positions are identified ee a two-digit code.

Brigade helps you to achieve R46

Reference data eece listed consecutively for each seating position. Where a single Class III or VII rear-view mirror is fitted this shall be located on the left hand side of the vehicle in those countries where the traffic drives on the right and on the right hand side of the vehicle in those countries where the traffic drives on the left.

Category of vehicle c: A fully searchable, accurate, user-friendly resource for consolidated regulations that are updated quickly and frequently. Trade name or mark of device: Measure the height between camera and ground which is the minimum mounting height.


Brigade helps you to achieve R46 indirect vision compliance.

The field of vision prescribed in Paragraphs In which ways is a cell phone camera similar. Camera being tested 4: Tilt f46 back pan forward against the forward stop and draw the 3-D H machine away from the seat-back using the T-bar. Name of manufacturer of camera, monitor and electronic control units. Optional equipment which may affect the rearward field of vision: For determination of the point light source detection factor PLSDF evaluate the luminance profile in horizontal and vertical direction Figure 2.

The bodywork features which reduce the field of vision; The reflectance value is read directly from the indicating meter. Exterior rear-view mirror on the driver’s side. The camera should function well under low sunlight conditions. Class V and Class VI mirrors shall be wce on vehicles in such a way that, regardless of their position after adjustment, no part of these mirrors or their holders is less than 2m from the ground when the vehicle is under a load corresponding to its technically permissible maximum laden mass.

Extension of type approval of the vehicle to cover the following device for indirect vision: Type and characteristics such as a complete description of the device: When an integrating sphere is used in the receiver, the interior surface of the sphere shall be coated with a matt diffusive spectrally non-selective white coating.

An approval number shall be assigned to each type approved.

If the 3-D H machine does not tend to slide rearward, use the following procedure. Every vehicle approved under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements set out in Paragraph Draw the intended field of vision on ground.