ECE R46 PDF

Official Journal of the European Union. EN. Only the original UN/ECE texts have legal effect under international public law. The status and date. Regulation No 46 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of devices for indirect. [ECE-R46 Uniform provisions concerning the approval of rear-view mirrors and of motor vehicles with regard to the installation of rear-view mirrors, MOD].

Author: Meztiramar Daikree
Country: Timor Leste
Language: English (Spanish)
Genre: Health and Food
Published (Last): 16 November 2008
Pages: 461
PDF File Size: 1.70 Mb
ePub File Size: 1.25 Mb
ISBN: 875-3-59656-955-7
Downloads: 98042
Price: Free* [*Free Regsitration Required]
Uploader: Arashirisar

Means of identification of type, if marked on the vehicle b: The receiver may incorporate a light-integrating sphere to facilitate measuring the reflectance of non-flat convex mirrors see Figure 2.

The field of vision shall be determined by placing powerful light sources at the ocular points and examining the light reflected on the vertical monitoring screen.

Brigade helps you to achieve R46

The index to the information package lodged with the Approval Authority, which may be obtained on request is attached. Spectral characteristics of light source and receiver. The procedure used dce clamp the mirror to the support shall be that recommended by the manufacturer of the device or, where appropriate, by the vehicle manufacturer. Main exterior rear-view mirrors Class II Reposition the 3-D H machine on the seat by one of the following methods: Test procedure The field of vision shall be determined by placing powerful light sources at the ocular points ecd examining the light reflected on the vertical monitoring screen.

InterRegs: Regulation No. | ECE – United Nations

General Specifications The Technical Service shall use recognized test methods to check compliance with the requirements defined above in the Regulation. Computer Graphics Lighting Jinxiang Chai. Reposition the 3-D H machine on the seat by one of the following methods:. Determination of the critical viewing distance of the monitor For a monitor having certain dimensions and properties, a distance to the monitor can be calculated within which the detection distance is dependent only on the performances of the camera.

  JISSEN MAGAZINE PDF

For a monitor having certain dimensions and properties, a distance to the monitor can be calculated within which the detection distance is dependent only on the performances of the camera.

R6 year, eec of people, mostly vulnerable road users such as pedestrians, cyclists and motorcyclists, are killed in incidents involving large goods vehicles. The centre of the monitor s shall not be below a plane passing through the driver’s ocular points, as defined in Paragraph Requirements for aspherical parts of mirrors 6.

Number of report issued by that Service: Mirrors state for each mirror: Monitor-side Figure 5 shows an example of a grey scale rendering chart to be used in this measurement.

Consider that the modifications made are unlikely to have an appreciable adverse effect, and that in any case the device for indirect vision still complies with the requirements; or 7. Penalties for Non-conformity of Production However, breakage of the reflecting surface will be allowed if one of the following conditions is fulfilled: Unless otherwise specified in this Regulation, the definitions and symbols used in Paragraph 6.

Technical Service responsible for carrying out the tests: Please leave this field empty. CIE spectral tristimulus values: The relationship of m o to the total mass m of the pendulum and to the distance d between the centre of gravity of the pendulum and its axis of rotation is expressed in the equation: Equipment A “spherometer” similar to the one described in Figure 1 of this Annex having the indicated distances between the tracing pin of the dial gauge and the fixed legs of the bar is used.

  KENNY BURRELL CHITLINS CON CARNE PDF

Photographs, if any, shall show sufficient detail.

All mirrors shall be adjustable. Nevertheless, the Technical Service responsible for testing may repeat one or both of these tests on the upper mirror if this is less than 2m from the ground.

ECE regulations: ECE R upglade

Type and general commercial description s … Means of identification of type, if marked on the vehicle: An example of the set-up is given in the Figure A below. This place shall be: Description of test The protective housing is placed horizontally in a device in such a way that it is possible to lock the attachment support adjusters firmly.

Position the camera of the CMS in front of a still scene e. The straight line joining these points runs perpendicular to ec vertical longitudinal median plane of the vehicle. Devices for indirect vision shall be so placed that the driver, when sitting on the driving seat in a normal driving position, has a clear view of the road to the rear, dce s or front of the vehicle. Camera-monitor Ecf The requirements of Paragraph 6.

Regulation 49 – 06 series (click to expand)

Obstruction of the driver’s direct view caused by the installation of a device for indirect vision shall be restricted to a minimum. When r4 look in a mirror, where is the face you see? Where possible the left foot shall be located approximately the same distance to the left of the centreplane of the 3-D H machine as the right foot is to the right.

Range of vehicle dimensions overall: CIE standard colorimetric observer: ecee