Manufacturer name, Eltako. Manufacturer number, TLZEV+UC. GTIN, Country of origin, Germany. Customs tariff number, gThe Standardg TLZ12 8E 23 V UC replaces the TLZ12N0 V and TLZ12 8E V+V uC. gThe Allrounderg TLZ12D 23 V UC replaces the TLZ12M V+V uC. g The Simpleg . Also visit TLZ12D V +UC. Eltako Staircase time switch TLZplus 1; 2; 3; 4 Matching products. Eltako Staircase time switchTLZ Manufacturer, Eltako. Manufacturer.
|Published (Last):||11 August 2009|
|PDF File Size:||7.92 Mb|
|ePub File Size:||16.70 Mb|
|Price:||Free* [*Free Regsitration Required]|
With incrementing the time can be extended and permanent light by pushbutton. Before working on the current transformers disconnect the voltage paths of the energy meters. Display up to tlz12-8e-23v0, kWh with 3 decimal digits, from 10kWh with 1 decimal digit and from kWh without decimal digit.
It is set to 5: Function rotary switchesStandard setting ex factory. The contact position is indicated by an arrow on the left in field 1.
When these staircase time switches are in ESL setting, the switch-off early warning by ickering function does not reduce the service life of the energy saving lamps. Degree of protection IP Voltage applied signalled by LED.
The accrued tz12-8e-230v time is displayed there outside the elapsed time, rst in hours hthen in months m with 1 digit after the decimal point.
Own elako light switch with the big rotary switch. State-of-the-art hybrid technology combines advantages of nonwearing electronic control with high capacity of special relays. Zero passage switching to protect contacts and consumers.
The load is switched on and off by a bistable relay at output EVG electronic ballast units. It blinks while the relay contact 15 is open 15 closedand is continuously ON as long as the relay contact 15 is closed 15 open. There are 5 ranges to choose from, starting on the left with 1, 3, 7, 15 and 30kW. Up or DOWN is activated by a control signal. The display then shows the total power per tariff and per resettable memory RS1 or RS2, and the instantaneous values of consumption, voltage and current per phase.
The colour of the button is always the same as the LED, the rest is blue. Accurate timing is self-evident for this electronic device as well as noiseless operation. It is set to 5: Also for dimmable energy saving lamps ESL. The internal powerconsumption of 0. Control voltage, supply voltage and switching voltage V. To adjust the CT ratio to the installed transformer remove the bridge and reset the energy meter according to the operation manual.
If the connection is tlz12-8e-230vv wired, the display shows the message ‘false’. Technical data page C A fold inrush current must be calculated for electronic ballast devices. A full telegram comprising toz12-8e-230v reading HT, meter reading NT and power is transmitted 20 seconds after the power supply is switched on and then every 10 minutes.
Depends on the set function. Safety in the event of a power failure: In this case, it is only for DOWN that the direction is reversed on time-out of the time lag selected by means of the top rotary switch, e. If the control voltage is removed during the wiping time the NO contact immediately reverts to and the residual time is cancelled.
In this way the energy consumption indicator reproduces exactly the reading on the billing energy meter installed tl1z2-8e-230v a different location in the building. The current dimming position as well Standard setting ex factory. Solid plastic housing, mm dia. With control impulses from 50 ms the make contact switches to and fro. VDEpart 1.
Universal control voltage Confirm the selected time by pressing MODE. A short interruption of control changes the direction of dimming. These determine which other control inputs areinhibited as long as onother control input is excited permanently.