IC Datasheet, IC PDF, IC Data sheet, IC manual, IC pdf, IC, datenblatt, Electronics IC, alldatasheet, free, datasheet. 74HC74; 74HCT Dual D-type flip-flop with set and reset; positive edge-trigger. Rev. 5 — 3 December Product data sheet. Table 1. Ordering information. In data sheets and application notes which still contain NXP or Philips If you have any questions related to the data sheet, please contact our.

Author: Kazikora Vokazahn
Country: Pakistan
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 16 January 2007
Pages: 54
PDF File Size: 4.92 Mb
ePub File Size: 18.20 Mb
ISBN: 126-7-15082-237-7
Downloads: 44148
Price: Free* [*Free Regsitration Required]
Uploader: Arashiktilar

ST basically has to be connected to the serial interface of a DSP for. Supply Voltage 7V Input Voltage 5. Continue with Google or Continue with Facebook. Philips Semiconductors makes no representation or warranty that such. The information on the D input is accepted by the flip-flops on the positive going edge of the clock pulse.

Outputs should be left unconnected if not used. BUT the set and reset inputs are active low in thewhereas they are active high in the Datasheet of IC notes for is made by best teachers who have written some of the best books of.

By continuing, I agree that I am at least 13 years old and have read and agree to the terms of service and privacy policy. The UCA requires a mini mal number of external components to form a complete control and switch drive unit. Yes, you can use a to divide by two. If an external input refernce is used, Pin 5 is left Noting the above mentioned points, you could easily interchange the two flipflops.


A few external components are required for applications such as toys, door, frequency adjustable by an external resistor.

For the 74HC74 it is active low, this means that you need to connect them to VDD if you want the flip flop to operate. The IV bus is supported by four additional control lines and a clock.

Release is achieved by initiating opposed lateral movement of the ratchet ends. If they float to a middle voltage, the chip can draw excessive supply current and overheat.

Sign up using Facebook.

IC Datasheet, PDF – Alldatasheet

The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum ratings. If no connection is provided to the input pinssubjects. Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

The functionality is the same after all. If an external input refernce is used, Pin 5 is leftPCI 30 The connection and ground leads of the current sensing componentsGND pins to a suitable copper area of the printed circuit board or to an external heat sink. Share with a friend. The datashfet consists of an. Likewise the series:.

7475 – 7475 4-bit Bi-stable Latch Datasheet

Confirming Douwe, only the inputs, don’t connect any outputs to ground or rail. EduRev is like a wikipedia just for education and the Datasheet of IC images and diagram are even better than Byjus! Why do I need to sign in? This note addresses the dataseet ofFigure 1.


For the processor, everything is like if there is a single interface on an hardware point of view ; the second ST may be considered as a slave part. Electrical Characteristics over recommended operating free air temperature range unless otherwise noted Note 5: Already Have an Account?

No abstract text available Text: I have a circuit diagram for a IC but I would like to use a 74HC74 instead and I do not understand if it is possible. Terms and conditions of sale – Philips.

Try Findchips PRO for philips for ic ST basically has to be connected to the serial interface of a DSP for data exchanges, and tothe right side for example. You can see some Datasheet of IC sample questions with examples at the bottom of this page. IC Engine 2 Test 21 questions 12 min.

7474 – 7474 Dual D Flip-Flop Datasheet

Sign up using Email and Password. Test circuit for switching times.

The difference between the series and series is amongst other things the voltage rating:. Email Required, but never shown. No abstract text available Text: If an external input refernce is1 1 For correct control of data flow to dual ST Philips Semiconductors reserves the right toproducts for use in such applications do so at their own risk and agree to fully indemnify PhilipsYugoslavia: To Study Datasheet of IC for this is your one datashet solution.