IEC TS Standard | Short-circuit current calculation in three-phase a.c. systems – Part 1: Factors for the calculation of short-circuit. IEC Short-Circuit Current Calculation in Three-Phase A.C. Systems Part 1: Factors for the Calculation of Short-Circuit Currents in Three-Phase A.C. IEC/TR Short-Circuit Currents in Three-Phase a.c. Systems – Part 1: Factors for the Calculation of Short-Circuit Currents According to IEC
|Published (Last):||22 December 2009|
|PDF File Size:||6.79 Mb|
|ePub File Size:||17.34 Mb|
|Price:||Free* [*Free Regsitration Required]|
The method described above is for 3-phase short circuit. The upstream circuit breakers do not trip instantaneously whereas the most downstream circuit breaker trips fast, enabling selective coordination. Form I-9 and E-Verify, getting and staying compliant.
Peak current based on method c: The program is designed to address short-circuits in meshed networks. Remote Currents and Voltages Currents flowing through sources, cables, lines, transformers and other equipment are also calculated. You can view the currents in various formats such as phase currents for A, B and C phases or in symmetrical components: Corresponding voltages can be displayed at the buses.
For remote buses and branches across transformers, a phase angle shift is applied accordingly by the short circuit calculations.
Breaking currents are calculated at 0. DC component of short-circuit current at breaking times: Earth ground trip functions for low voltage circuit breakers or relays use the symmetrical earth ie current.
Short-circuit currents in three-phase a. The short-circuit impedances for electrical equipment are modified using impedance corrections factors that are calculated based on section 3. Peak current based on method 609909-1 The values can be displayed in magnitude, magnitude and angle, or in real and imaginary quantities.
Take the smart route to manage medical device compliance. IEC section 6 provides a sample calculation as a benchmark test for software programs to compare. Case Management Boot Ice Steady-state short-circuit current I k Steady-state short-circuit current I k is calculated based on section 4.
IEC-60909 Short-Circuit in EasyPower
These remote currents and voltages are useful for relay setting. In a system of low voltage breakers with ZSI, when the current through any circuit breaker exceeds the short time pickup its restraining signal is sent to upstream circuit breakers. Voltage sensitivity report for buses with voltage below 609091- Transformer Phase Shift The short-circuit calculation provides the phase angle of the branch currents and the bus voltages at various equipment. The phase angles displayed are relative to the applied equivalent voltage source being at 609091- angle.
Measurement management systems – Requirements for measurement processes and measuring equipment. For high voltage circuit breakers, the peak current is compared with the making capacity and the breaking current is compared with the rated breaking capacity. EasyPower offers a complete and accurate solution to short-circuit calculations in three-phase AC systems using the IEC standard.
Account Payable Best Practices: The comparison of results is summarized below. Short-circuit equipment duty report Voltage Sensitivity Analysis Short-circuit on any bus results in voltage drop in other near buses in the system.
Motor contributions are excluded.
High voltage circuit breaker data comes with the DC time constant. The following features are supported:.
This will display the curve only up to the maximum current the device will see. This factor is also used in calculating impedance correction factors. EasyPower provides the option of showing a warning when the short-circuit duty percent is above a user defined safety uec threshold but below the violation level.
The implementation is as per sections 4. View of the single line diagram in the time current characteristics TCC plot for protective devices. Short-circuit on any bus results in voltage drop in other near buses in the system. Protecting Revenues with Advanced Compliance: EasyPower supports the following four types of short-circuit conditions as per IEC Switches use the peak current to compare with making capacity. Fuses and low voltage circuit breakers ratings are compared with initial currents.
Highlighting of buses when voltage is below threshold Figure 7: Specifications and FDA Requirements. Transformers having different winding configurations, such as a delta connection on one side and a star wye connection on the other side, have a designated shift in the phase angles of currents and voltages.
IEC TR | IEC Webstore
The short-circuit calculation provides the phase angle of the branch currents and the bus voltages at various equipment. Example HV breaker ratings in the device library Figure 4: Please download Chrome or Firefox or view our browser tips. Your basket is empty.